Vinyl Record Display Brackets | Album Wall Decor | LP Holder
from £5.99
These adjustable Vinyl Display Mounts are the ultimate way to display your records and treat them as works of art.
Designed and 3d printed by me in Lincolnshire in the UK, this solution is a beautifully flexible way to show off your collection. Each set includes two brackets, four Command Strips (for damage-free, removable hanging) and a set of six spacers (three of each size) so that whether it's a single, double or even triple gatefold, your brackets will hold it. You can choose whatever colour you like, too.
(The last photo shows the colourless (frosted) option, so you can see how it looks.)
Please read below for fitting instructions.
-------
Spacing...
First decide where you want your display. For a good horizontal spacing you might consider a 40cm (15.5") gap from the side of one bracket to the next. This will give you a 7.5cm (3") gap between your records, so you can adjust that if you want a different spacing. Then set your vertical spacing accordingly.
(Using this spacing a 2x2 square will make a 27" (66cm) square on the wall. A 3x3 square will be 42" (107cm) square.)
Instructions...
* Place two Command Strips on the back of each bracket, with the straight edges aligned to the outside edges of the back of the bracket and the tabs visible through the middle. (See pictures for example.) Make sure you stick the side with the red text to the back of the bracket. The black text side is for the wall.
* Using a spirit level, line your bottom bracket up first and then stick to the wall. Press firmly on the back surface of the bracket for 10 seconds.
* Place a sleeve on the bottom bracket and line up the top bracket, then stick it to the wall. Be careful to line it up vertically with the lower bracket. Remove the sleeve.
* Clip a spacer into the space on the back of each shelf (use the same size in both brackets), then wait an hour before sliding your sleeve in from the side.
* Enjoy.
Any questions or issues please get in touch. I can do custom orders and I can offer discounts for large batches.
Thanks
Rob
Designed and 3d printed by me in Lincolnshire in the UK, this solution is a beautifully flexible way to show off your collection. Each set includes two brackets, four Command Strips (for damage-free, removable hanging) and a set of six spacers (three of each size) so that whether it's a single, double or even triple gatefold, your brackets will hold it. You can choose whatever colour you like, too.
(The last photo shows the colourless (frosted) option, so you can see how it looks.)
Please read below for fitting instructions.
-------
Spacing...
First decide where you want your display. For a good horizontal spacing you might consider a 40cm (15.5") gap from the side of one bracket to the next. This will give you a 7.5cm (3") gap between your records, so you can adjust that if you want a different spacing. Then set your vertical spacing accordingly.
(Using this spacing a 2x2 square will make a 27" (66cm) square on the wall. A 3x3 square will be 42" (107cm) square.)
Instructions...
* Place two Command Strips on the back of each bracket, with the straight edges aligned to the outside edges of the back of the bracket and the tabs visible through the middle. (See pictures for example.) Make sure you stick the side with the red text to the back of the bracket. The black text side is for the wall.
* Using a spirit level, line your bottom bracket up first and then stick to the wall. Press firmly on the back surface of the bracket for 10 seconds.
* Place a sleeve on the bottom bracket and line up the top bracket, then stick it to the wall. Be careful to line it up vertically with the lower bracket. Remove the sleeve.
* Clip a spacer into the space on the back of each shelf (use the same size in both brackets), then wait an hour before sliding your sleeve in from the side.
* Enjoy.
Any questions or issues please get in touch. I can do custom orders and I can offer discounts for large batches.
Thanks
Rob
Primary color:
How many pairs of brackets?:
Quantity:
These adjustable Vinyl Display Mounts are the ultimate way to display your records and treat them as works of art.
Designed and 3d printed by me in Lincolnshire in the UK, this solution is a beautifully flexible way to show off your collection. Each set includes two brackets, four Command Strips (for damage-free, removable hanging) and a set of six spacers (three of each size) so that whether it's a single, double or even triple gatefold, your brackets will hold it. You can choose whatever colour you like, too.
(The last photo shows the colourless (frosted) option, so you can see how it looks.)
Please read below for fitting instructions.
-------
Spacing...
First decide where you want your display. For a good horizontal spacing you might consider a 40cm (15.5") gap from the side of one bracket to the next. This will give you a 7.5cm (3") gap between your records, so you can adjust that if you want a different spacing. Then set your vertical spacing accordingly.
(Using this spacing a 2x2 square will make a 27" (66cm) square on the wall. A 3x3 square will be 42" (107cm) square.)
Instructions...
* Place two Command Strips on the back of each bracket, with the straight edges aligned to the outside edges of the back of the bracket and the tabs visible through the middle. (See pictures for example.) Make sure you stick the side with the red text to the back of the bracket. The black text side is for the wall.
* Using a spirit level, line your bottom bracket up first and then stick to the wall. Press firmly on the back surface of the bracket for 10 seconds.
* Place a sleeve on the bottom bracket and line up the top bracket, then stick it to the wall. Be careful to line it up vertically with the lower bracket. Remove the sleeve.
* Clip a spacer into the space on the back of each shelf (use the same size in both brackets), then wait an hour before sliding your sleeve in from the side.
* Enjoy.
Any questions or issues please get in touch. I can do custom orders and I can offer discounts for large batches.
Thanks
Rob
Designed and 3d printed by me in Lincolnshire in the UK, this solution is a beautifully flexible way to show off your collection. Each set includes two brackets, four Command Strips (for damage-free, removable hanging) and a set of six spacers (three of each size) so that whether it's a single, double or even triple gatefold, your brackets will hold it. You can choose whatever colour you like, too.
(The last photo shows the colourless (frosted) option, so you can see how it looks.)
Please read below for fitting instructions.
-------
Spacing...
First decide where you want your display. For a good horizontal spacing you might consider a 40cm (15.5") gap from the side of one bracket to the next. This will give you a 7.5cm (3") gap between your records, so you can adjust that if you want a different spacing. Then set your vertical spacing accordingly.
(Using this spacing a 2x2 square will make a 27" (66cm) square on the wall. A 3x3 square will be 42" (107cm) square.)
Instructions...
* Place two Command Strips on the back of each bracket, with the straight edges aligned to the outside edges of the back of the bracket and the tabs visible through the middle. (See pictures for example.) Make sure you stick the side with the red text to the back of the bracket. The black text side is for the wall.
* Using a spirit level, line your bottom bracket up first and then stick to the wall. Press firmly on the back surface of the bracket for 10 seconds.
* Place a sleeve on the bottom bracket and line up the top bracket, then stick it to the wall. Be careful to line it up vertically with the lower bracket. Remove the sleeve.
* Clip a spacer into the space on the back of each shelf (use the same size in both brackets), then wait an hour before sliding your sleeve in from the side.
* Enjoy.
Any questions or issues please get in touch. I can do custom orders and I can offer discounts for large batches.
Thanks
Rob
These adjustable Vinyl Display Mounts are the ultimate way to display your records and treat them as works of art.
Designed and 3d printed by me in Lincolnshire in the UK, this solution is a beautifully flexible way to show off your collection. Each set includes two brackets, four Command Strips (for damage-free, removable hanging) and a set of six spacers (three of each size) so that whether it's a single, double or even triple gatefold, your brackets will hold it. You can choose whatever colour you like, too.
(The last photo shows the colourless (frosted) option, so you can see how it looks.)
Please read below for fitting instructions.
-------
Spacing...
First decide where you want your display. For a good horizontal spacing you might consider a 40cm (15.5") gap from the side of one bracket to the next. This will give you a 7.5cm (3") gap between your records, so you can adjust that if you want a different spacing. Then set your vertical spacing accordingly.
(Using this spacing a 2x2 square will make a 27" (66cm) square on the wall. A 3x3 square will be 42" (107cm) square.)
Instructions...
* Place two Command Strips on the back of each bracket, with the straight edges aligned to the outside edges of the back of the bracket and the tabs visible through the middle. (See pictures for example.) Make sure you stick the side with the red text to the back of the bracket. The black text side is for the wall.
* Using a spirit level, line your bottom bracket up first and then stick to the wall. Press firmly on the back surface of the bracket for 10 seconds.
* Place a sleeve on the bottom bracket and line up the top bracket, then stick it to the wall. Be careful to line it up vertically with the lower bracket. Remove the sleeve.
* Clip a spacer into the space on the back of each shelf (use the same size in both brackets), then wait an hour before sliding your sleeve in from the side.
* Enjoy.
Any questions or issues please get in touch. I can do custom orders and I can offer discounts for large batches.
Thanks
Rob
Designed and 3d printed by me in Lincolnshire in the UK, this solution is a beautifully flexible way to show off your collection. Each set includes two brackets, four Command Strips (for damage-free, removable hanging) and a set of six spacers (three of each size) so that whether it's a single, double or even triple gatefold, your brackets will hold it. You can choose whatever colour you like, too.
(The last photo shows the colourless (frosted) option, so you can see how it looks.)
Please read below for fitting instructions.
-------
Spacing...
First decide where you want your display. For a good horizontal spacing you might consider a 40cm (15.5") gap from the side of one bracket to the next. This will give you a 7.5cm (3") gap between your records, so you can adjust that if you want a different spacing. Then set your vertical spacing accordingly.
(Using this spacing a 2x2 square will make a 27" (66cm) square on the wall. A 3x3 square will be 42" (107cm) square.)
Instructions...
* Place two Command Strips on the back of each bracket, with the straight edges aligned to the outside edges of the back of the bracket and the tabs visible through the middle. (See pictures for example.) Make sure you stick the side with the red text to the back of the bracket. The black text side is for the wall.
* Using a spirit level, line your bottom bracket up first and then stick to the wall. Press firmly on the back surface of the bracket for 10 seconds.
* Place a sleeve on the bottom bracket and line up the top bracket, then stick it to the wall. Be careful to line it up vertically with the lower bracket. Remove the sleeve.
* Clip a spacer into the space on the back of each shelf (use the same size in both brackets), then wait an hour before sliding your sleeve in from the side.
* Enjoy.
Any questions or issues please get in touch. I can do custom orders and I can offer discounts for large batches.
Thanks
Rob
