Em Exibição, Portuguese On Show DVD and Blu ray Frame
£29.99
You've put a DVD or blu-ray on for the evening, but what do you do with the case? Sling it on the side? Terrible idea. Especially when you could put it in your incredible Em Exibição stand.
This one's a bit different to my other stands, in that I had to produce separate parts and then assemble them. All parts are 3d printed separately and then assembled with CA glue for a strong hold.
I'll send it assembled, so all you have to do is find a good place to put it, and enjoy.
These are intended for standard sized cases. DVDs will fit and fill top to bottom, blu-rays will fit in the slightly deeper recess. You probably won't fit box-sets. I considered whether to make them work for those but I think with so much variation I'd have had to make them with loads of tolerance and it wouldn't have looked as tidy as it does with singles, so I stuck with that. (If you want one made to a bespoke size just let me know and I can put something together for you for a small design fee.) The little nub on the right in the recess is there to hold your case. You might not need it, but if you do then you just need to press firmly to engage it. It's a tight fit, but it won't damage your case.
This is 3d printed, so there will be some surface texture. Because it's mostly black though you won't see much of the texture unless you're up close looking for it.
So there we go. I hope you like it.
This one's a bit different to my other stands, in that I had to produce separate parts and then assemble them. All parts are 3d printed separately and then assembled with CA glue for a strong hold.
I'll send it assembled, so all you have to do is find a good place to put it, and enjoy.
These are intended for standard sized cases. DVDs will fit and fill top to bottom, blu-rays will fit in the slightly deeper recess. You probably won't fit box-sets. I considered whether to make them work for those but I think with so much variation I'd have had to make them with loads of tolerance and it wouldn't have looked as tidy as it does with singles, so I stuck with that. (If you want one made to a bespoke size just let me know and I can put something together for you for a small design fee.) The little nub on the right in the recess is there to hold your case. You might not need it, but if you do then you just need to press firmly to engage it. It's a tight fit, but it won't damage your case.
This is 3d printed, so there will be some surface texture. Because it's mostly black though you won't see much of the texture unless you're up close looking for it.
So there we go. I hope you like it.
Quantity:
You've put a DVD or blu-ray on for the evening, but what do you do with the case? Sling it on the side? Terrible idea. Especially when you could put it in your incredible Em Exibição stand.
This one's a bit different to my other stands, in that I had to produce separate parts and then assemble them. All parts are 3d printed separately and then assembled with CA glue for a strong hold.
I'll send it assembled, so all you have to do is find a good place to put it, and enjoy.
These are intended for standard sized cases. DVDs will fit and fill top to bottom, blu-rays will fit in the slightly deeper recess. You probably won't fit box-sets. I considered whether to make them work for those but I think with so much variation I'd have had to make them with loads of tolerance and it wouldn't have looked as tidy as it does with singles, so I stuck with that. (If you want one made to a bespoke size just let me know and I can put something together for you for a small design fee.) The little nub on the right in the recess is there to hold your case. You might not need it, but if you do then you just need to press firmly to engage it. It's a tight fit, but it won't damage your case.
This is 3d printed, so there will be some surface texture. Because it's mostly black though you won't see much of the texture unless you're up close looking for it.
So there we go. I hope you like it.
This one's a bit different to my other stands, in that I had to produce separate parts and then assemble them. All parts are 3d printed separately and then assembled with CA glue for a strong hold.
I'll send it assembled, so all you have to do is find a good place to put it, and enjoy.
These are intended for standard sized cases. DVDs will fit and fill top to bottom, blu-rays will fit in the slightly deeper recess. You probably won't fit box-sets. I considered whether to make them work for those but I think with so much variation I'd have had to make them with loads of tolerance and it wouldn't have looked as tidy as it does with singles, so I stuck with that. (If you want one made to a bespoke size just let me know and I can put something together for you for a small design fee.) The little nub on the right in the recess is there to hold your case. You might not need it, but if you do then you just need to press firmly to engage it. It's a tight fit, but it won't damage your case.
This is 3d printed, so there will be some surface texture. Because it's mostly black though you won't see much of the texture unless you're up close looking for it.
So there we go. I hope you like it.
You've put a DVD or blu-ray on for the evening, but what do you do with the case? Sling it on the side? Terrible idea. Especially when you could put it in your incredible Em Exibição stand.
This one's a bit different to my other stands, in that I had to produce separate parts and then assemble them. All parts are 3d printed separately and then assembled with CA glue for a strong hold.
I'll send it assembled, so all you have to do is find a good place to put it, and enjoy.
These are intended for standard sized cases. DVDs will fit and fill top to bottom, blu-rays will fit in the slightly deeper recess. You probably won't fit box-sets. I considered whether to make them work for those but I think with so much variation I'd have had to make them with loads of tolerance and it wouldn't have looked as tidy as it does with singles, so I stuck with that. (If you want one made to a bespoke size just let me know and I can put something together for you for a small design fee.) The little nub on the right in the recess is there to hold your case. You might not need it, but if you do then you just need to press firmly to engage it. It's a tight fit, but it won't damage your case.
This is 3d printed, so there will be some surface texture. Because it's mostly black though you won't see much of the texture unless you're up close looking for it.
So there we go. I hope you like it.
This one's a bit different to my other stands, in that I had to produce separate parts and then assemble them. All parts are 3d printed separately and then assembled with CA glue for a strong hold.
I'll send it assembled, so all you have to do is find a good place to put it, and enjoy.
These are intended for standard sized cases. DVDs will fit and fill top to bottom, blu-rays will fit in the slightly deeper recess. You probably won't fit box-sets. I considered whether to make them work for those but I think with so much variation I'd have had to make them with loads of tolerance and it wouldn't have looked as tidy as it does with singles, so I stuck with that. (If you want one made to a bespoke size just let me know and I can put something together for you for a small design fee.) The little nub on the right in the recess is there to hold your case. You might not need it, but if you do then you just need to press firmly to engage it. It's a tight fit, but it won't damage your case.
This is 3d printed, so there will be some surface texture. Because it's mostly black though you won't see much of the texture unless you're up close looking for it.
So there we go. I hope you like it.
